Rod Ends Series K  -  standard

Series         GI Rod Ends with female thread made from free-cutting or heat-treated steel, zinc plated and with lubrication fittings. Especially suited for axial loads.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co  kN	Dynamic load C  kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	27	36	11	9,0	7,7	9	M 5	10	9,9	2,5	900	18	0,03969
6	9	6,75	20	30	40	13	10,0	8,9	11	M 6	12	11,9	3,2	760	27	0,059535
8	12	9,00	24	36	48	16	12,5	10,4	13	M 8	16	17,1	5,4	620	46	0,10143
10	14	10,50	28	43	57	19	15,0	12,9	17	M 10	20	21,4	7,5	500	76	0,16758
12	16	12,00	32	50	66	22	17,5	15,4	19	M 12	22	27,1	10,0	450	115	0,253575
14	19	13,50	36	57	75	25	20,0	16,8	22	M 14	25	24,5	12,9	360	170	0,37485
16	21	15,00	42	64	85	27	22,0	19,3	22	M 16	28	37,1	16,1	350	230	0,50715
18	23	16,50	46	71	94	31	25,0	21,8	27	M 18x1,5	32	43,1	19,6	320	320	0,7056
20	25	18,00	50	77	102	34	27,5	24,3	32	M 20x1,5	33	49,5	23,6	280	415	0,915075
22	28	20,00	54	84	111	37	30,0	25,8	32	M 22x1,5	37	57,3	28,6	250	540	1,1907
25	31	22,00	60	94	124	42	33,5	29,6	36	M 24x2	42	67,8	35,4	230	750	1,65375

Materials:

Housing:	up to size 12 turned from free-cutting steel to 9SMnPb28K,
	from size 14 forged from heat-treated steel to C22
Insert:	special brass to CuZn40Al1
Ball:	bearing steel to 100Cr6, hardened, ground, polished

Rod Ends Series K  -  standard

Series         GA Rod Ends with male thread made from free-cutting or heat-treated steel, zinc plated with lubrication fittings. Especially suited for axial loads.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co  kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	33	42	7,7	M 5	20	4,3	2,5	900	13	0,028665
6	9	6,75	20	36	46	8,9	M 6	22	6,0	3,2	760	20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	11,0	5,4	620	33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	17,4	7,5	500	56	0,12348
12	16	12,00	32	57	70	15,4	M 12	33	25,3	10,0	450	87	0,191835
14	19	13,50	36	60	78	16,8	M 14	36	24,5	12,9	360	129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	36,4	16,1	350	189	0,416745
18	23	16,50	46	72	95	21,8	M 18x1,5	44	43,1	19,6	320	267	0,588735
20	25	18,00	50	78	103	24,3	M 20x1,5	47	49,5	23,6	280	348	0,76734
22	28	20,00	54	84	111	25,8	M 22x1,5	51	57,3	28,6	250	443	0,976815
25	31	22,00	60	94	124	29,6	M 24x2	57	67,8	35,4	230	600	1,323

Materials:

Housing:	up to size 12 turned from free-cutting steel to 9SMnPb28K,
	from size 14 forged from heat-treated steel to C22
Insert:	special brass to CuZn40Al1
Ball:	bearing steel to 100Cr6, hardened, ground, polished

Rod Ends Series K  -  heavy duty

Series         GIS Rod Ends with female thread made from free-cutting or heat-treated steel, zinc plated and with lubrication fittings. Especially suited for high speed applications.

Size (D)	B	M	A	^F	L	K	J	O	SW	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
2	4,8	3,60	9	16	20,5	4,5	3,8	3,6	4,0	M 2	7	3,0	1,15	1400	3	0,006615
3	6,0	4,50	14	21	27,0	6,5	5,0	5,1	5,5	M 3	10	4,1	1,8	1300	6	0,01323
5	8,0	6,00	18	27	36,0	11,0	9,0	7,7	9,0	M 5	10	8,0	3,3	1200	18	0,03969
6	9,0	6,75	20	30	40,0	13,0	10,0	8,9	11,0	M 6	12	8,9	4,3	1500	27	0,059535
8	12,0	9,00	24	36	48,0	16,0	12,5	10,4	13,0	M 8	16	14,1	7,1	1200	46	0,10143
10	14,0	10,50	28	43	57,0	19,0	15,0	12,9	17,0	M 10	20	19,3	10,0	1000	76	0,16758
12	16,0	12,00	32	50	66,0	22,0	17,5	15,4	19,0	M 12	22	23,5	13,3	860	115	0,253575
14	19,0	13,50	36	57	75,0	25,0	20,0	16,8	22,0	M 14	25	20,8	17,1	750	170	0,37485
16	21,0	15,00	42	64	85,0	27,0	22,0	19,3	22,0	M 16	28	32,0	21,4	660	230	0,50715
18	23,0	16,50	46	71	94,0	31,0	25,0	21,8	27,0	M 18x1,5	32	38,6	26,2	600	320	0,7056
20	25,0	18,00	50	77	102,0	34,0	27,5	24,3	32,0	M 20x1,5	33	43,8	31,4	540	415	0,915075
22	28,0	20,00	54	84	111,0	37,0	30,0	25,8	32,0	M 22x1,5	37	52,6	38,1	500	540	1,1907
25	31,0	22,00	60	94	124,0	42,0	33,5	29,6	36,0	M 24x2	42	62,4	47,1	440	750	1,65375
30	37,0	25,00	70	110	145,0	51,0	40,0	34,8	41,0	M 30x2	51	81,6	63,5	370	1130	2,49165
35	43,0	28,00	80	125	165,0	56,0	46,0	37,7	50,0	M 36x2	56	100,8	80,0	330	1600	3,528
40	49,0	35,00	90	142	187,0	69,0	57,0	44,2	60,0	M 42x2	60	124,0	115,5	290	2770	6,10785

Materials:

Housing:	up to size 12 turned from free-cutting steel to 9SMnPb28K,
	from size 14 forged from heat-treated steel to C22
Insert:	special high strength bronze to CuSn8
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).
	Rod Ends series K  -  heavy duty

Series         GAS Rod Ends with male thread made from free-cutting or heat-treated steel, zinc plated and fitted with a lubrication fitting. Especially suited for high speed applications.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
2	4,8	3,60	9	20	24,5	3,6	M 2	12	0,6	1,1	1400	3	0,006615
3	6,0	4,50	14	26	33,0	5,1	M 3	15	1,5	1,8	1300	6	0,01323
5	8,0	6,00	18	33	42,0	7,7	M 5	20	4,3	3,3	1200	13	0,028665
6	9,0	6,75	20	36	46,0	8,9	M 6	22	6,0	4,3	1500	20	0,0441
8	12,0	9,00	24	42	54,0	10,4	M 8	25	11,0	7,1	1200	33	0,072765
10	14,0	10,50	28	48	62,0	12,9	M 10	29	17,4	10,0	1000	56	0,12348
12	16,0	12,00	32	54	70,0	15,4	M 12	33	23,5	13,3	860	87	0,191835
14	19,0	13,50	36	60	78,0	16,8	M 14	38	20,8	17,1	750	129	0,284445
16	21,0	15,00	42	66	87,0	19,3	M 16	40	32,0	21,4	660	189	0,416745
18	23,0	16,50	46	72	95,0	21,8	M 18x1,5	44	38,6	26,2	600	267	0,588735
20	25,0	18,00	50	78	103,0	24,3	M 20x1,5	47	43,8	31,4	540	348	0,76734
22	28,0	20,00	54	84	111,0	25,8	M 22x1,5	51	52,6	38,1	500	443	0,976815
25	31,0	22,00	60	94	124,0	29,6	M 24x2	58	62,4	47,1	440	600	1,323
30	37,0	25,00	70	110	145,0	34,8	M 30x2	71	81,6	63,5	370	1030	2,27115
35	43,0	28,00	80	125	165,0	37,7	M 36x2	77	100,8	80,0	330	1600	3,528
40	49,0	35,00	90	142	187,0	44,2	M 42x2	78	124,0	115,5	290	2550	5,62275

Materials:

Housing:	up to size 12 turned from free-cutting steel to 9SMnPb28K,
	from size 14 forged from heat-treated steel to C22
Insert:	special high strength bronze to CuSn8
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  extra heavy duty

Series         GIXS Rod Ends with female thread made from free-cutting or heat-treated steel, zinc plated and regreasable through lubrication fitting in the housing. Especially suitable for high pressure and tension loads.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
6	9	6,75	20	30	40	13	10,0	8,9	11	M 6	12	16,7	4,3	1500	27	0,059535
8	12	9,00	24	36	48	16	12,5	10,4	13	M 8	16	25,5	7,1	1200	46	0,10143
10	14	10,50	28	43	57	19	15,0	12,9	17	M 10	20	34,8	10,0	1000	76	0,16758
12	16	12,00	32	50	66	22	17,5	15,4	19	M 12	22	42,2	13,3	860	115	0,253575
14	19	13,50	36	57	75	25	20,0	16,8	22	M 14	25	56,9	17,1	750	170	0,37485
16	21	15,00	42	64	85	27	22,0	19,3	22	M 16	28	67,7	21,4	660	230	0,50715
18	23	16,50	46	71	94	31	25,0	21,8	27	M 18x1,5	32	81,4	26,2	600	320	0,7056
20	25	18,00	50	77	102	34	27,5	24,3	32	M 20x1,5	33	93,7	31,4	540	415	0,915075
22	28	20,00	54	84	111	37	30,0	25,8	32	M 22x1,5	37	113,8	38,1	500	540	1,1907
25	31	22,00	60	94	124	42	33,5	29,6	36	M 24x2	42	135,4	47,1	440	750	1,65375
30	37	25,00	70	110	145	51	40,0	34,8	41	M 30x2	51	184,4	63,5	370	1130	2,49165

Materials:

Housing:	heat-treated steel to 42CrMo4, forged
Insert:	special high strength bronze to CuSn8
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  extra heavy duty

Series         GAXS Rod Ends with male thread made from free-cutting or heat-treated steel, zinc plated and regreasable through lubrication fitting in the housing. Especially suitable for high pressure and tension loads.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co   kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
6	9	6,75	20	36	46	8,9	M 6	22	9,8	4,3	1500	20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	19,5	7,1	1200	33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	31,4	10,0	1000	56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	42,2	13,3	860	87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	56,9	17,1	750	129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	67,7	21,4	660	189	0,416745
18	23	16,50	46	72	95	21,8	M 18x1,5	44	81,4	26,2	600	267	0,588735
20	25	18,00	50	78	103	24,3	M 20x1,5	47	93,7	31,4	540	348	0,76734
22	28	20,00	54	84	111	25,8	M 22x1,5	51	113,8	38,1	500	443	0,976815
25	31	22,00	60	94	124	29,6	M 24x2	58	135,4	47,1	440	600	1,323
30	37	25,00	70	110	145	34,8	M 30x2	71	184,4	63,5	370	1030	2,27115

Materials:

Housing:	heat-treated steel to 42CrMo4, forged
Insert:	special high strength bronze to CuSn8
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  stainless

Series         GIRS Rod Ends with female thread made from stainless steel, regreasable through lubrication fittings in the housing. For use in corrosive environments.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
3	6	4,50	14	21	27	6,5	5,0	5,1	5,5	M 3	10	8,0	1,8	1300	6	0,01323
5	8	6,00	18	27	36	11,0	9,0	7,7	9,0	M 5	10	11,8	3,3	1200	18	0,03969
6	9	6,75	20	30	40	13,0	10,0	8,9	11,0	M 6	12	13,1	4,3	1500	27	0,059535
8	12	9,00	24	36	48	16,0	12,5	10,4	13,0	M 8	16	20,7	7,1	1200	46	0,10143
10	14	10,50	28	43	57	19,0	15,0	12,9	17,0	M 10	20	28,3	10,0	1000	76	0,16758
12	16	12,00	32	50	66	22,0	17,5	15,4	19,0	M 12	22	34,5	13,3	860	115	0,253575
14	19	13,50	36	57	75	25,0	20,0	16,8	22,0	M 14	25	39,4	17,1	750	170	0,37485
16	21	15,00	42	64	85	27,0	22,0	19,3	22,0	M 16	28	60,6	21,4	660	230	0,50715
18	23	16,50	46	71	94	31,0	25,0	21,8	27,0	M 18x1,5	32	73,2	26,2	600	320	0,7056
20	25	18,00	50	77	102	34,0	27,5	24,3	32,0	M 20x1,5	33	83,1	31,4	540	415	0,915075
22	28	20,00	54	84	111	37,0	30,0	25,8	32,0	M 22x1,5	37	99,7	38,1	500	540	1,1907
25	31	22,00	60	94	124	42,0	33,5	29,6	36,0	M 24x2	42	118,3	47,1	440	750	1,65375
30	37	25,00	70	110	145	50,0	40,0	34,8	41,0	M 30x2	51	154,8	63,5	370	1130	2,49165
35	43	28,00	80	125	165	58,0	46,0	37,7	50,0	M 36x2	56	191,2	80,0	330	1600	3,528

Materials:

Housing:	stainless steel to 1.4057, forged, polished
Insert:	special high strength bronze to CuSn8
Ball:	bearing steel to 100Cr6, hardened, ground, polished, hard chrome plated
On request:	the ball can be made from stainless steel to 1.4034 hardened, ground, polished, or to 1.4401 ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  stainless

Series         GARS Rod Ends with male thread made from stainless steel, regreasable through lubrication fittings in the housing. For use in corrosive environments.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co   kN	Dynamic load C   kN	Limiting speed rev/min	Weight gram	Weight lb.
3	6	4,50	14	26	33	5,1	M 3	15	7,0	1,8	1300	6	0,01323
5	8	6,00	18	33	42	7,7	M 5	20	6,2	3,3	1200	13	0,028665
6	9	6,75	20	36	46	8,9	M 6	22	8,8	4,3	1500	20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	16,1	7,1	1200	33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	25,5	10,0	1000	56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	34,5	13,3	860	87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	39,4	17,1	750	129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	60,6	21,4	660	189	0,416745
18	23	16,50	46	72	95	21,8	M 18x1,5	44	73,2	26,2	600	267	0,588735
20	25	18,00	50	78	103	24,3	M 20x1,5	47	83,1	31,4	540	348	0,76734
22	28	20,00	54	84	111	25,8	M 22x1,5	51	99,7	38,1	500	443	0,976815
25	31	22,00	60	94	124	29,6	M 24x2	58	118,3	47,1	440	600	1,323
30	37	25,00	70	110	145	34,8	M 30x2	71	154,8	63,5	370	1030	2,27115
35	43	28,00	80	125	165	37,7	M 36x2	77	191,2	80,0	330	1600	3,528

Materials:

Housing:	stainless steel to 1.4057, forged, polished
Insert:	special high strength bronze to CuSn8
Ball:	bearing steel to 100Cr6, hardened, ground, polished, hard chrome plated
On request:	The ball can be made from stainless steel to 1.4034 hardened, ground, polished, or to 1.4401 ground, polished.

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  maintenance free

Series         GISW Rod Ends with female thread made from free-cutting or heat-treated steel, zinc  plated with PTFE liner, maintenance free. For use at lower revs and dynamic load.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	27	36	11	9,0	7,7	9,0	M 5	10	8,0	7,5	600	18	0,03969
6	9	6,75	20	30	40	13	10,0	8,9	11,0	M 6	12	8,9	9,3	530	27	0,059535
8	12	9,00	24	36	48	16	12,5	10,4	13,0	M 8	16	14,1	16,7	420	46	0,10143
10	14	10,50	28	43	57	19	15,0	12,9	17,0	M 10	20	19,3	23,4	350	76	0,16758
12	16	12,00	32	50	66	22	17,5	15,4	19,0	M 12	22	23,5	32,0	300	115	0,253575
14	19	13,50	36	57	75	25	20,0	16,8	22,0	M 14	25	20,8	41,9	260	170	0,37485
16	21	15,00	42	64	85	27	22,0	19,3	22,0	M 16	28	32,0	52,7	230	230	0,50715
18	23	16,50	46	71	94	31	25,0	21,8	27,0	M 18x1,5	32	38,6	63,8	210	320	0,7056
20	25	18,00	50	77	102	34	27,5	24,3	32,0	M 20x1,5	33	43,8	78,1	190	415	0,915075
22	28	20,00	54	84	111	37	30,0	25,8	32,0	M 22x1,5	37	52,6	97,2	170	540	1,1907
25	31	22,00	60	94	124	42	33,5	29,6	36,0	M 24x2	42	62,4	122,1	150	750	1,65375
30	37	25,00	70	110	145	51	40,0	34,8	41,0	M 30x2	51	81,6	168,4	130	1130	2,499165
35	43	28,00	80	125	165	56	46,0	37,7	50,0	M 36x2	56	100,8	205,7	110	1600	3,528
40	49	35,00	90	142	187	69	57,0	44,2	60,0	M 42x2	60	124,0	297,1	100	2770	6,10785

Materials:

Housing:	up to size 12 turned, from free-cutting steel to 9SMnPb28K,
	from size 14 forged, from heat-treated steel to C22
Insert:	free-cutting steel to 9SMnPb28K with PTFE liner bonded to the inner surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  maintenance free

Series         GASW Rod Ends with male thread made from free-cutting or heat-treated steel, zinc plated with PTFE liner (maintenance free). For use at lower revs and dynamic loads.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co kN	Dynamic load C  kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	33	42	7,7	M 5	20	4,3	7,5	600	13	0,028665
6	9	6,75	20	36	46	8,9	M 6	22	6,0	9,3	530	20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	11,0	16,7	420	33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	17,4	23,4	350	56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	23,5	32,0	300	87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	20,8	41,9	260	129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	32,0	52,7	230	189	0,416745
18	23	16,50	46	72	95	21,8	M 18x1,5	44	38,6	63,8	210	267	0,588735
20	25	18,00	50	78	103	24,3	M 20x1,5	47	43,8	78,1	190	348	0,76734
22	28	20,00	54	84	111	25,8	M 22x1,5	51	52,6	97,2	170	443	0,976815
25	31	22,00	60	94	124	29,6	M 24x2	58	61,4	122,1	150	600	1,323
30	37	25,00	70	110	145	34,8	M 30x2	71	81,6	168,4	130	1030	2,27115
35	43	28,00	80	125	165	37,7	M 36x2	77	100,8	205,7	110	1600	3,528
40	49	35,00	90	142	187	44,2	M 42x2	78	124,0	297,1	100	2570	5,66685

Materials:

Housing:	up to size 12 turned, from free-cutting steel to 9SMnPb28K,
	from size 14 forged, from heat-treated steel to C22
Insert:	free-cutting steel to 9SMnPb28K with PTFE liner bonded to the inner surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  maintenance free

Series         GIXSW Rod Ends with female thread made from heat-treated steel, zinc plated, with PTFE liner, maintenance free. For use at lower revs and high pressure and tension loads.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co kN	Dynamic loads C kN	Limiting speed rev/min	Weight gram	Weight lb.
6	9	6,75	20	30	40	13	10,0	8,9	11	M 6	12	16,7	9,3	530	27	0,0595335
8	12	9,00	24	36	48	16	12,5	10,4	13	M 8	16	25,5	16,7	420	46	0,10143
10	14	10,50	28	43	57	19	15,0	12,9	17	M 10	20	34,8	23,4	350	76	0,16758
12	16	12,00	32	50	66	22	17,5	15,4	19	M 12	22	42,2	32,0	300	115	0,253575
14	19	13,50	36	57	75	25	20,0	16,8	22	M 14	25	56,9	41,9	260	170	0,37485
16	21	15,00	42	64	85	27	22,0	19,3	22	M 16	28	67,7	52,7	230	230	0,50715
18	23	16,50	46	71	94	31	25,0	21,8	27	M 18x1,5	32	81,4	63,8	210	320	0,7056
20	25	18,00	50	77	102	34	27,5	24,3	32	M 20x1,5	33	93,7	78,1	190	415	0,915075
22	28	20,00	54	84	111	37	30,0	25,8	32	M 22x1,5	37	113,8	97,2	170	540	1,1907
25	31	22,00	60	94	124	42	33,5	29,6	36	M 24x2	42	135,4	122,1	150	750	1,65375
30	37	25,00	70	110	145	51	40,0	34,8	41	M 30x2	51	184,4	168,4	130	1130	2,49165

Materials:

Housing:	heat-treated steel to 42CrMo4, forged
Insert:	free-cutting steel to 9SMnPb28K with PTFE liner, bonded to the inner surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  maintenance free

Series         GAXSW Rod Ends with male thread made from heat-treated steel, zinc plated, with PTFE liner (maintenance free). For use at lower revs and high pressure and tension loads.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
6	9	6,75	20	36	46	8,9	M 6	22	9,8	9,3	530	20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	19,5	16,7	420	33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	31,4	23,4	350	56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	42,2	32,0	300	87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	56,9	41,9	260	129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	67,7	52,7	230	189	0,416745
18	23	16,50	46	72	95	21,8	M 18x1,5	44	81,4	63,8	210	267	0,588735
20	25	18,00	50	78	103	24,3	M 20x1,5	47	93,7	78,1	190	348	0,76734
22	28	20,00	54	84	111	25,8	M 22x1,5	51	113,8	97,2	170	443	0,976815
25	31	22,00	60	94	124	29,6	M 24x2	58	135,4	122,1	150	600	1,323
30	37	25,00	70	110	145	34,8	M 30x2	71	184,4	168,4	130	1030	2,27115

Materials:

Housing:	heat-treated steel to 42CrMo4, forged
Insert:	free-cutting steel to 9SMnPb28K with PTFE liner, bonded to the inner surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  - maintenance free

Series         GIOW Rod Ends with female thread made from free-cutting or heat-treated steel, zinc plated and maintenance free. For use in applications involving minimum axial loads and limited oscillating movements.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co  kN	Dynamic load C   kN	Limiting speed rev/min	Weight gram	Weight lb.
4	7	5,25	14	24	31	9,5	7,8	6,5	8	M 4	12	5,2	0,8	not to be used for complete revolutions	11	0,024255
5	8	6,00	18	27	36	11,0	9,0	7,7	9	M 5	10	9,8	1,1		18	0,03969
6	9	6,75	20	30	40	13,0	10,0	8,9	11	M 6	12	11,8	1,4		27	0,059535
8	12	9,00	24	36	48	16,0	12,5	10,4	13	M 8	16	17,3	2,2		46	0,10143
10	14	10,50	28	43	57	19,0	15,0	12,9	17	M 10	20	22,3	3,1		76	0,16758
12	16	12,00	32	50	66	22,0	17,5	15,4	19	M 12	22	28,3	3,9		115	0,253575
14	19	13,50	36	57	75	25,0	20,0	16,8	22	M 14	25	26,0	4,8		170	0,37485
16	21	15,00	42	64	85	27,0	22,0	19,3	22	M 16	28	38,9	7,0		230	0,50715
20	25	18,00	50	77	102	34,0	27,5	24,3	32	M 20x1,5	33	52,8	9,7		415	0,915075

Materials:

Housing:	up to size 12 turned from free-cutting steel to 9SMnPb28K,
	from size 14 forged from heat-treated steel to C22,
	PTFE glass fibre fabric on the running surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished

Rod Ends Series K  -  maintenance free

Series         GAOW Rod Ends with male thread made from free-cutting or heat-treated steel, zinc plated, maintenance free. For use in applications involving minimum axial loads and limited oscillating movements.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
4	7	5,25	14	30	37	6,5	M 4	19	2,6	0,8	not to be used for complete revolutions	9	0,019845
5	8	6,00	18	33	42	7,7	M 5	20	4,3	1,1		13	0,028665
6	9	6,75	20	36	46	8,9	M 6	22	6,0	1,4		20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	11,0	2,2		33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	17,4	3,1		56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	25,3	3,9		87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	26,0	4,8		129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	36,4	7,0		189	0,416745
20	25	18,00	50	78	103	24,3	M 20x1,5	47	52,8	9,7		348	0,76734

Materials:

Housing:	up to size 12 turned from free-cutting steel to 9SMnPb28K,
	from size 14 forged from heat-treated steel to C22,
	PTFE glass fibre fabric on the running surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished

Rod Ends Series K  -  stainless, maintenance free

Series         GIRSW Rod Ends with female thread made from stainless steel with PTFE liner, maintenance free. For use at lower revs and high pressure and tension loads in corrosive environments.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	27	36	11,0	9,0	7,7	9	M 5	10	11,8	7,5	600	18	0,03969
6	9	6,75	20	30	40	13,0	10,0	8,9	11	M 6	12	13,1	9,3	530	27	0,059535
8	12	9,00	24	36	48	16,0	12,5	10,4	13	M 8	16	20,7	16,7	420	46	0,10143
10	14	10,50	28	43	57	19,0	15,0	12,9	17	M 10	20	28,3	23,4	350	76	0,16758
12	16	12,00	32	50	66	22,0	17,5	15,4	19	M 12	22	34,5	32,0	300	115	0,253575
14	19	13,50	36	57	75	25,0	20,0	16,8	22	M 14	25	39,4	41,9	260	170	0,37485
16	21	15,00	42	64	85	27,0	22,0	19,3	22	M 16	28	60,6	52,7	230	230	0,50715
18	23	16,50	46	71	94	31,0	25,0	21,8	27	M 18x1,5	32	73,2	63,8	210	320	0,7056
20	25	18,00	50	77	102	34,0	27,5	24,3	32	M 20x1,5	33	83,1	78,1	190	415	0,915075
22	28	20,00	54	84	111	37,0	30,0	25,8	32	M 22x1,5	37	99,7	97,2	170	540	1,1907
25	31	22,00	60	94	124	42,0	33,5	29,6	36	M 24x2	42	118,3	122,1	150	750	1,65375
30	37	25,00	70	110	145	50,0	40,0	34,8	41	M 30x2	51	154,8	168,4	130	1130	2,49165
35	43	28,00	80	125	165	58,0	46,0	37,7	50	M 36x2	56	191,2	205,7	110	1600	3,528

Materials:

Housing:	stainless steel to 1.4057, forged, polished
Insert:	special high strength bronze to CuSn8 with PTFE liner bonded to the inner surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished, hard chrome plated
On request:	Insert: stainless steel to 1.4571 Ball: stainless steel to 1.4034 hardened, ground, polished or in stainless steel to 1.4401 ground, polished

This series is also available sealed (-2RS) or with threaded  bolt (-BO).

Rod Ends Series K  -  stainless, maintenance free

Series         GARSW Rod Ends with male thread made from stainless steel with PTFE liner, maintenance free. For use at lower revs and high pressure and tension loads in corrosive environments.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co kN	dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	33	42	7,7	M 5	20	6,2	7,5	600	13	0,028665
6	9	6,75	20	36	46	8,9	M 6	22	8,8	9,3	530	20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	16,1	16,7	420	33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	25,5	23,4	350	56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	34,5	32,0	300	87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	39,4	41,9	260	129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	60,6	52,7	230	189	0,416745
18	23	16,50	46	72	95	21,8	M 18x1,5	44	73,2	63,8	210	267	0,588735
20	25	18,00	50	78	103	24,3	M 20x1,5	47	83,1	78,1	190	348	0,76734
22	28	20,00	54	84	111	25,8	M 22x1,5	51	99,7	97,2	170	443	0,976815
25	31	22,00	60	94	124	29,6	M 24x2	58	118,3	122,1	150	600	1,323
30	37	25,00	70	110	145	34,8	M 30x2	71	154,8	168,4	130	1030	2,27115
35	43	28,00	80	125	165	37,7	M 36x2	77	191,2	205,7	110	1600	3,528

Materials:

Housing:	stainless steel to 1.4057, forged, polished
Insert:	special high strength bronze to CuSn8 with PTFE liner bonded to the inner surface
Ball:	bearing steel to 100Cr6, hardened, ground, polished, hard chrome plated
On request:	Insert:  stainless steel to 1.4571 Ball:  stainless steel to 1.4034 hardened, ground, polished or in stainless steel 1.4401 ground, polished

This series is also available sealed (-2RS) or with threaded bolt (-BO).

Rod Ends Series K  -  steel on steel

Series         GIO Rod Ends with female thread made from free-cutting or heat-treated steel, zinc plated without the insert, running surface steel on steel. High axial load in one direction only. To be used only with limited oscillating movements.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co  kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	27	36	11	9,0	7,7	9	M 5	10	12,0	2,2	not to be used for complete revo- lutions	18	0,03969
6	9	6,75	20	30	40	13	10,0	8,9	11	M 6	12	14,3	2,8		27	0,059535
8	12	9,00	24	36	48	16	12,5	10,4	13	M 8	16	21,7	4,6		46	0,10143
10	14	10,50	28	43	57	19	15,0	12,9	17	M 10	20	27,8	6,5		76	0,16758
12	16	12,00	32	50	66	22	17,5	15,4	19	M 12	22	35,1	8,7		115	0,253575
14	19	13,50	36	57	75	25	20,0	16,8	22	M 14	25	32,4	11,1		170	0,37485
16	21	15,00	42	64	85	27	22,0	19,3	22	M 16	28	46,1	13,9		230	0,50715
20	25	18,00	50	77	102	34	27,5	24,3	32	M 20x1,5	33	62,8	20,4		415	0,915075

Materials:

Housing:	up to size 12  turned, from free-cutting steel to 9SMnPb28K,
	from size 14 forged, from heat-treated steel to C22
Ball:	bearing steel to 100Cr6, hardened, ground, polished

The base in the steel housing is cylindrically turned from one side and, starting from the centre line, it runs to suit the ball's contour (see drawing above).
Hence a high axial load towards the turned radius is possible.

Rod Ends Series K  -  steel on steel

Series         GAO Rod Ends with male thread made from free-cutting or heat-treated steel, zinc plated without the insert, running surface steel on steel. High axial load in one direction only. To be used only with limited oscillating movements.

Size (D)	B	M	A	F	L	O	G	GL	Static load Co  kN	Dynamic load C kN	Limiting speed rev/min	Weight gram	Weight lb.
5	8	6,00	18	33	42	7,7	M 5	20	4,3	2,2	not to be used for complete revolutions	13	0,028665
6	9	6,75	20	36	46	8,9	M 6	22	6,0	2,8		20	0,0441
8	12	9,00	24	42	54	10,4	M 8	25	11,0	4,6		33	0,072765
10	14	10,50	28	48	62	12,9	M 10	29	17,4	6,5		56	0,12348
12	16	12,00	32	54	70	15,4	M 12	33	25,3	8,7		87	0,191835
14	19	13,50	36	60	78	16,8	M 14	38	26,7	11,1		129	0,284445
16	21	15,00	42	66	87	19,3	M 16	40	36,4	13,9		189	0,416745
20	25	18,00	50	78	103	24,3	M 20x1,5	47	62,8	20,4		348	0,76734

Materials:

Housing:	up to size 12 turned, from free-cutting steel to 9SMnPb28K,
	from size 14 forged, from heat-treated steel to C22
Ball:	bearing steel to 100Cr6, hardened, ground, polished

The base in the steel housing is cylindrically turned from one side and, starting from the centre line, it runs to suit the ball's contour (see drawing above).
Hence a high axial load towards the turned radius is possible.

Rod Ends Series K  -  with threaded bolt

Series         G...-BO Rod Ends and Spherical Plain Bearings with threaded bolt. For use as a right angle connector: - G.S - G.XS - G.RS - G.SW - G.XSW - G.RSW

Size	L	L1	GL	G	D	SW	Weight of bolt gram	Weight of bolt lb.
6	18,5	5,5	10	M 6	9,0	8	10	0,02205
8	23,5	6,5	13	M 8	10,5	8	12	0,02646
10	28,0	7,0	17	M 10	13,0	12	25	0,055125
12	32,5	7,5	20	M 12	15,0	14	40	0,0882
14	37,5	8,5	22	M 14	17,0	14	65	0,143325
16	42,5	9,5	24	M 16	19,0	17	90	0,19845

Materials:

Rod Ends and Sphericals:	see description of respective version
Threaded bolt:	free-cutting steel to 9SMnPb28K, zinc plated or stainless steel to 1.4305

Rod Ends Series K  -  CETOP

Rod Ends for pneumatic cylinders to CETOP RP 103 P All female Rod Ends series are available with CETOP dimensions for pneumatic cylinders. Connections to ISO 8139.

Size (D)	B	M	A	F	L	K	J	O	SW	G	GL	Static load Co  kN	Dynamic load C kN	Limiting speed rev/min	for cylinder-Ø
5	8	6,00	18	27	36	11	9,0	7,7	9	M 4	10	for load details see respective version			8 + 10
6	9	6,75	20	30	40	13	10,0	8,9	11	M 6	12				12 + 16
8	12	9,00	24	36	48	16	12,5	10,4	13	M 8	16				20
10	14	10,50	28	43	57	19	15,0	12,9	17	M 10x1,25	20				25 + 32
12	16	12,00	32	50	66	22	17,5	15,4	19	M 12x1,25	22				40 + 50
16	21	15,00	42	64	85	27	22,0	19,3	22	M 16x1,5	28				50 + 63
20	25	18,00	50	77	102	34	27,5	24,3	32	M 20x1,5	33				80 + 100
25	31	22,00	60	94	124	42	33,5	29,6	36	M 24x2	42				125
30	37	25,00	70	110	145	51	40,0	34,8	41	M 27x2	51				125
35	43	28,00	80	125	165	56	46,0	37,7	50	M 36x2	56				160 + 200
40	49	35,00	90	142	187	69	57,0	44,2	60	M 42x2	60				250

Materials:

	see respective versions
Ordering details:	please specify when ordering Rod Ends series and thread, for example:
	GI 10x1,25
	GISW 16x1,5
	GIRSW 30 M27x2